Hardwood Floor Refinishing
Sand, stain, and dustless-finish worn floors back to a like-new look without replacing a single board.

Canton, GA · Serving Cherokee County
Canton is close enough to our Woodstock home base that it might as well be our backyard — a straight shot up I-575 and we're there. It's also a city with two very different faces right now. Downtown Canton has spent the last several years restoring its historic core, with older homes that often have original hardwood worth bringing back to life. A few minutes away, Riverstone and the newer subdivisions built up around the I-575 corridor are mostly ten-to-fifteen-year-old homes on their first or second floor refinish.
We hold ourselves to the same standard whether the job is a historic downtown bungalow or a Riverstone two-story.
In Canton the subfloor decides the product. A wood subfloor takes solid hardwood nailed down, and a concrete slab calls for engineered boards that are glued or floated. Our hardwood floor installation page and our engineered hardwood page set the two side by side. In kitchens, baths and basements we install LVP, including COREtec and NuCore, and AquaGuard laminate suits kitchens and finished basements that pass a moisture check.
One Canton job used both kinds of hardwood. Engineered white oak went over the concrete main level and solid white oak went upstairs, finished to match. Video posted August 2026. Another Canton floor was 7-inch red oak stained warm gray and fastened with glue and nails. Video posted May 2025. Both are listed under Canton Hardwood Floor Projects.
If the wood is sound, refinishing is the answer, whether the floor is original to a downtown house or a Riverstone floor on its first refinish. A finish that is dull but intact may need only a screen and recoat. Boards that are damaged, loose or stained can often go through hardwood floor repairs, and we replace only the boards that cannot be saved. If a leak damaged the floor, we document and repair the damage, your homeowner’s policy decides coverage, and we respond the same business day; see water-damaged floor repair in Canton.
Our Dark Walnut refinish in Canton started with a newly purchased home and aging floors. They were water-popped, stained Dark Walnut and finished with Bona Traffic HD, and the stair treads, handrails and posts were refinished to match. Video posted September 2026. Its card is under Canton Hardwood Floor Projects, and the video is under Watch Our Work in Canton, GA.
Call 470-826-3581 or request a free estimate online. We serve downtown Canton, Riverstone, and all of Cherokee County, and we’re open 24/7.
A member of The Hardwood Guys team will call or text you to schedule your free on-site estimate. We schedule 24/7.
Our Canton refinishing video follows a newly purchased home with aging floors. The homeowner wanted them updated with a rich Dark Walnut stain and asked for a fast-drying finish, so we recommended and applied Bona Traffic HD, a water-based finish. For the general process, see our hardwood floor refinishing page.
Dark colors depend on preparation. We water-popped these floors before staining, which opens the pores of the wood so the color goes in deep and even and shows the natural grain. The house has large windows and a lot of natural light, so a flat surface mattered. We sanded with our HyperGrinder I-4 planetary sander to keep the floors flat and leave a clean scratch pattern before finishing.
The scope went past refinishing. New hardwood went into the master bedroom and upstairs hallway and was blended in with the rest of the home, and the stair treads, handrails and posts were refinished to match. The homeowner was pleased with the result.
Video posted September 2026 · Watch the Dark Walnut refinish on YouTube
A second Canton video also used planetary sanding, with a Hypergrinder I4, followed by a Weathered Oak stain and Bona Traffic HD. That job removed water-damaged planks and installed a new floor, so it is covered in the water-damage section below. Watch it on YouTube (Video posted February 2026).
A floor that only needs its shine back may need nothing more than a screen and recoat. To talk through yours, request a free estimate.
New hardwood in a Canton home starts with one decision: solid or engineered. The subfloor usually makes it for you, and the Canton installs we have filmed show both choices.
Engineered where there is concrete. On one Canton job the main level sat on a concrete subfloor, so we installed factory-finished, live-sawn engineered white oak, and the boards on that job were 5/8 inch thick with a 4 mm wear layer. A wear layer that thick can be sanded and refinished more than once. Another Canton install used 7-inch-wide engineered planks, and that construction gives the stability needed for installs over concrete slabs.
Solid where it fits. On that same white oak job, the second floor got 3/4-inch solid white oak finished on site with Bona Natural Seal and Bona Traffic HD, so it reads as a near match for the engineered floor downstairs. A different Canton home got 7-inch character-grade red oak, stained warm gray and installed with both glue and nails to limit gapping in winter.
New homes and older ones. We have worked in the Great Sky neighborhood, in Riverstone, and in older homes near downtown. In the newer subdivisions along I-575, we can put hardwood into a room that still has builder-grade carpet. We also add to existing floors: one Canton home got new hardwood in the master bedroom and upstairs hallway, blended with the rest of the house, and the stairs were refinished to match. In older Canton homes we plan for surprises under the old floor, such as an earlier patch or flooring nailed over flooring. One Canton job started by tearing out water-damaged, thin builder-grade engineered planks.
Watch the Canton installation videos below, read more about hardwood floor installation and engineered hardwood, or request a free estimate.
Solid hardwood is nailed down, so it needs a wood subfloor to nail into. Engineered boards are usually glued or floated, and they suit a concrete slab. Neither type is better in every house. Either way, we check the subfloor and its moisture before anything goes down. One Canton job shows the engineered side: water-damaged, builder-grade thin engineered planks came out, and 5/8-inch live sawn white oak engineered flooring went in (watch it on YouTube, Video posted February 2026). Compare the options on our engineered hardwood flooring page.
The Canton water job we have on video is Project Highlight: Custom Live Sawn White Oak Engineered Transformation in Canton, Georgia (Video posted February 2026). It was a complete flooring overhaul. We began by removing the water-damaged, builder-grade thin engineered planks, and the finished floor restored the home after the water damage.
The new floor is live sawn white oak engineered, 5/8 inch thick with a 4 mm wear layer, finished on site with a Weathered Oak stain and Bona Traffic HD. We sanded it with the Hypergrinder I4 planetary sander to get a flat surface.
A cupped board was wetter underneath than on top, whether from a leak that soaked in or from moisture coming up through a slab, crawlspace or wet subfloor. A crowned board usually means the floor was sanded before it finished drying. A buckled board has lifted off the subfloor and usually has to be replaced. Before any sanding, we take moisture readings on the boards and on the subfloor, so the decision rests on numbers instead of how the floor looks that week. We will not sell a full sand over a wet crawlspace that is still feeding moisture.
Three outcomes are possible. A spot repair cuts out the bad boards and blends the color. A refinish fits a floor whose boards are mostly sound but whose finish failed. Replacement is for boards whose wear layer or core will not take another sand.
We document and repair. Your homeowner's policy decides coverage. When you call or text photos of the damage, we respond the same business day. Until we get there, stop the leak, pull up rugs and run a dehumidifier if you have one.
Our post on water-damaged hardwood repair in Canton and Acworth sums up what drives the decision: how much water reached the floor, how long it stayed wet and whether the finish is still sealing the wood. It names basement leaks, dishwasher lines and storm water at sliding doors as the usual sources. For the full process, see our water-damaged hardwood floor repair page, or request a free estimate.
Sand, stain, and dustless-finish worn floors back to a like-new look without replacing a single board.
Solid and engineered hardwood installed with a subfloor and moisture check first.
Waterproof-rated vinyl plank, including COREtec and NuCore, for kitchens, baths and basements, and AquaGuard laminate for kitchens and finished basements.
Fix squeaks, gouges, water stains, and pet damage — repaired to match the surrounding floor.
Screen-and-recoat and deep cleaning that extends the life of your floors between full refinishes.
Premium natural-look finishes — Rubio Monocoat, Bona Craft Oil, and Pallmann Magic Oil — for a low-sheen, low-VOC result.
Real Canton jobs, each from a video we filmed on site. Details come from our own write-up of each job.
A newly purchased Canton home with aging floors, refinished in Dark Walnut and finished with Bona Traffic HD. New hardwood went into the master bedroom and upstairs hallway, and the stair treads, handrails and posts were refinished to match.

7-inch-wide, character-grade red oak installed in a Canton home, stained warm gray and finished on site with matte oil-based polyurethane. The boards were glued and nailed to help limit gapping in winter.


A Canton home that got factory-finished engineered white oak over the concrete main level and 3/4-inch solid white oak upstairs. The upstairs planks were finished on site with Bona Natural Seal and Bona Traffic HD to match the engineered floor below.
Real jobs, real homeowners, real floors — filmed on site. Nothing plays until you press it, so the page stays fast.
Hardwood Floor Transformation in Canton, GA: Dark Walnut Stain and Bona HD Traffic
White Oak Flooring Installation in Canton, GA
7-Inch Red Oak Hardwood Floor Installation in Canton, GA
Live Sawn White Oak Engineered Floor in Canton, Georgia
7-Inch Wide Plank Engineered Hardwood Installation, Canton, GA
We have 10,000 jobs completed in Georgia, serving Cherokee County, including Canton, from just up the road in Woodstock. Being this close means faster scheduling and a crew that already knows the area. Reviews are written by real customers.
If your Canton home is a downtown historic house where the original hardwood has been painted over, covered in old carpet padding residue, or worn through the finish after decades of use, a full sand and refinish can often bring those floors back. In Riverstone and the newer subdivisions, engineered hardwood that is ten years old and just needs its shine back may only need a screen and recoat, and a room that still has builder-grade carpet can get new hardwood.
“From the first phone call I had a great experience with The Hardwood Guys. They were very responsive, did a great job on the floors, and kept to the schedule which was very important for us.”
10,000 jobs completed in Georgia
Financing available — up to $100,000, with interest-free options from $30/mo. Subject to approval.
Cupped or buckled floors after a leak? We repair, replace and refinish matching boards and document the damage. Your homeowner's policy decides coverage. See water-damaged hardwood floor repair.
Related: water-damaged hardwood repair in Canton and Acworth
Usually faster than most of our service area — Canton is a short drive up I-575 from our home base, which means less windshield time and more flexibility on scheduling.
Yes, regularly. We're comfortable matching stain and finish on original hardwood in older homes, not just installing new floors in newer construction.
Yes, that can happen in Riverstone. Builder-grade finish on the main level takes a beating from daily foot traffic, and by the ten-to-fifteen-year mark it's usually worn thin in the hallways and kitchen entry even if the rest of the floor still looks fine. It doesn't mean anything went wrong — it's just the normal life span of that original factory finish.
No, we work around original trim whenever we can rather than pulling it out. We tape and protect the baseboards during sanding and finishing, and we're careful with the edger near them so we don't chip old woodwork that can't easily be replaced. In some cases we'll add shoe molding afterward to hide the expansion gap, but the trim itself usually stays put.
Yes. On a first refinish there's usually plenty of wood to work with, so it's fairly standard sanding. By the second time around, we're paying closer attention to how much board thickness is left before we hit a nail head or the tongue and groove. We sand lighter and check more carefully as we go, because there's less room for error than there was the first time.
Pretty often, yes. Older Canton homes have usually had some kind of patch job done over the years — a section replaced with mismatched boards, subfloor damage under an old water stain, or flooring nailed right over another layer of flooring. None of that is unusual, and most of it is fixable. We just like to set expectations up front instead of surprising you with it mid-job.
A crowned board is higher in the middle than at the edges. It usually means the floor was sanded flat while it was still drying, and the boards shrank afterward. Once the floor is fully dry and the readings on the boards and subfloor are normal, it can often be sanded flat again if there is enough wood left above the tongue. If there is not, the affected boards are replaced.
Only when we need to see the edge of the floor. A photo of the room can hide soft spots under the kick, so on some wet floors we take the base off and check before we recommend a repair.
We began by removing the water-damaged, builder-grade thin engineered planks. The replacement was live sawn white oak engineered flooring, 5/8 inch thick with a 4 mm wear layer, finished on site with a Weathered Oak stain and Bona Traffic HD. We sanded with a Hypergrinder I4 planetary sander to get a flat surface. Video posted February 2026.